Chemicals Needed for Muscle Contraction

Chemicals Needed for Muscle ContractionThe goal for this lab was to train the conditions that demonstrate what chemicals in muscle fibers are necessary for compaction and which virtuosos prevent muscle contraction from occurring in a simplified system in narrate to determine the minimum fatality for contraction.MethodsIn order to prepare muscle fibers, a single cheat was obtained from a mass of glycerinated muscle fibers which was about 0.5 mm in diameter. The muscle was a rabbit psoas muscle in 50% glycerol (stored at -10 degrees C) obtained from Carolina Biological. In order to get to an observation of what was taking berth with the muscle, Nikon E400 was use. The fiber was placed on a slide in the presence of 0.05 M KCl and 0.005 M K phosphate buffer (pH 7). The first step was to sight the minimum requirement solution for muscle contraction to take place. This was done by using the following solutions 0.001 M MgCl2, 0.001 M CaCl2, and 0.1 M adenosine triphosphate. The req uirement was resolute after observing the changes taking place when each of the solutions were added to the muscle separately, in combinations of two, and all three solutions together.After the minimum requirement was determined, chelators were used to see whether they control contraction in the presence of the solution that caused contraction. The chelators were 0.002 M EDTA and 0.002M EGTA. The EDTA binds Ca ++ and Mg ++. EGTA binds only Ca++. The chelating agents enhance the solubility of magnesium and calcium and allow them to permeate out of the muscle fibers. This causes the removal of the ions from the actin and myosin environment. It was important that the chelators were added before the contracting agents when inhibition was being tested. Otherwise, it would be impossible to detect any changes once the contraction has interpreted place contraction is not reversible once it occurs in a simplified system.Then Solution A and Solution B were used to shew the localization of myosin and actin in the myofibrils. Solution As function was to solubilize and remove myosin in the form of monomers from its loci which is in the myofibril. Solution B had the same behavior as the actin. The Solutions were placed on the myofibril to see changes that took place and observations were made.Discussion and ConclusionDuring this lab, using the microscope we examined the changes that took place when certain solution were introduced to the rabbit psoas muscle fibers. The solutions caused contraction, inhibited contraction to occur, or had no effect on the sarcomeres at all. We used glycerinated myofibrils from rabbit psoas muscle which is a type of striated muscle. Rabbit psoas muscle was a good forge to use for this lab since the fibers are long and straight. Also one other advantage was that there were not a lot of connective tissues connecting the muscle fibers together. This was an in vitro model meaning that experiment was completed outside the living organism.The P hase Contrast with magnification of 10X/ 40X was used during this lab to examine the slide because the cells are artless and Phase Contrast is the best option to use in order to have a good resolution. Under a microscope the myofibers were striated and they had a repeating variety of bands and lines. The pattern was caused by parallel organization of protein filaments within the myofibrils. In the myofibril, there are two types of filament- the thick filaments which consist of the protein myosin and thin filaments composed of the protein actin.As demonstrate on Table 1, Mg2Cl2, Ca2Cl2, and adenosine triphosphate were the solution used to determine the changes taking place with the muscle. All of the three solutions were placed on the slide which consisted of a thread of muscle fiber and contraction of the muscle was observed. We could tell when contraction was taking place because the fiber was short in length and it was easy to see the changes such as the shortening in length a nd the color change. When Mg2Cl2 and Ca2Cl2 were added individually to the fiber, nothing happened. However, as soon as the adenosine triphosphate was placed on changes were easily observed. adenosine triphosphate caused muscle contraction by itself. The sarcomeres in the muscle fiber shortened in length and the color changed from light yellow to darker yellow.However, in order to brand name sure this was the minimum requirement for muscle contraction, we added Mg2Cl2 with ATP and Ca2Cl2 with ATP.With the MgCl2 and ATP, the contraction occurred immediately as the solutions were added. The contraction was even faster than the ATP alone. Then ATP and Ca2Cl2 solutions were introduced and this in any case caused contraction. Even though the combination of the two solutions caused contraction to occur faster than ATP by itself, it was slower than the solutions of ATP and Mg2Cl2. As a result, we concluded that ATP was the minimum requirement needed for the cells to contract. All the sol utions that caused contraction were not in one dimension because every component of a sarcomere was facing changes except the A band which stayed the same. The I bands, the M line, the Z lines, and the actin and mysosin- they were all decreasing in length in order to cause contraction. At the end, it was determined that ATP was the requirement for glycerinated muscle contraction. When there is no ATP present, the myosin heads in the muscle will not be activated and it would not bind to the actin. In glycerinated tissues, the combination of KCl and MgCl2 with ATP increased the strength of muscle contraction. This was mainly due to myosins high affinity for these ions.Table 2 shows whether contraction was inhibited in the presence of chelating agents, EDTA and EGTA, when it was used with the main solution that caused contraction, ATP. EDTA and EGTA did not inhibit contraction from taking place, but the contraction was slower than when ATP was present. EDTA is a chelating agent that bi nds Ca++ and Mg++ and EGTA is a chelating agent that binds Ca++. The chelating agents increase the solubility of Mg 2+ and Ca2+ so that they can leave the muscle fibers. With ATP and the chelating agents, contraction occurred and there was no inhibition taking place.Table 3 shows two different solutions, Solution A and solution B, and their effect on actin and myosin. As shown in the table, solution A had KCl, phosphate buffer, Na pyrophosphate, and MgCl2 while solution B had phosphate buffer. Both of these solutions did not cause any contraction in the muscle based on our observations. However, changes were discernable because in both cases the fibers changed color they became lighter yellow. This meant that the muscles were not contracting. Solution A made the mysosin more soluble and solution B acted in the same modal value as the actin.When comparing the muscle in living tissue, the glycerinated muscle system is different. The glycerination technique eliminates ions and ATP fro m the tissue and disrupts the troponin/tropomyosin complex. When the complex is interrupted, the available binding sites on the actin fibers are no longer blocked ( Cell and Molecular Biology). As a result, Ca2+ is not one of the requirements to cause contraction. On the other hand, since there is no ATP is in the glycerinated tissue, the myosin heads cannot be activated to cause contraction. After the muscle contracted it did not relax since there were no opposing muscles to pull it. Also, muscle fibers do not contract when there are no stimulations or nerve signals and this was one of the differences with glycerinated muscle and the living cell muscle.Errors could have occurred in this lab if one used very thick muscle strands. Having thinner strands were better to have good results. Also, it is possible that much of the calcium was still in the sarcoplasmic reticulum of the glycerinated muscle, which would have lead into incorrect results. All in all however, the lab was successf ul and we have obtained what we were looking for- what solutions cause contraction, which ones inhibit, and what is the minimum requirement for muscle contraction.